Introduction

• All safety instructions described below are intended to protect the user and other individuals from physical harm and property damage.
• Safety instructions are classified and described as shown below according to the level of harm or damage resulting from improper use.

Description of Symbols

To Page Top

Precautions for use

Warning

• Keep out of reach of children. Do not allow children to play with the product.
  There is a risk of scalds* or other injuries.
  * When using products that keep beverages hot.

  

Caution

• Do not disassemble or attempt to repair this product.
  There is a risk of product failure or accident.
  Do not place the product on its side.
  The contents may spill out. When putting the product in a bag or other container, place the product in an upright position.

• Do not use the product if you can hear water moving around* within the double-layer vacuum structure (vacuum layer) of its body.
  Drinking from the product may cause you to feel unwell if water from the vacuum layer seeps into the interior of the product. In the case of the heat retention type, there is a risk of burns caused by the body heating up when hot beverages are poured into the product.
  *A rattling sound may be heard when shaking its body. This is caused by rubbing of metallic foil placed inside the body to improve the heat retention effect, but it poses no problems with respect to usage.
  <How to check heat retention effect>
  Fill the body with hot water and touch the center of the bottom of the body after about five minutes. If the body is hot, discontinue use of the product, as it has no heat retention effect.

  

• Do not use the product to hold anything other than beverages.
  If drank by accident there is a risk of burns, scalding* or other injuries.
  * When using products that keep beverages hot.
• Do not place the product near stoves, open flames, or other sources of extreme heat.
  There is a risk of burns or deformation or discoloration of the product.
• Do not heat the product in a microwave oven.
  There is a risk of failure of the microwave due to sparking. There is also a risk of burns or deformation or discoloration of the product.
• Do not put the product in a freezer.
  The beverage may leak, the product may be damaged, or the performance of the product may decrease.
• Do not knock over, drop, or strike the product or expose it to excessive shocks or vibration.
  There is a risk of damage to the product, reduction of its performance, rusting, paint/printing/plating peeling*, or leakage of contents.
  * For products that are painted, plated, or include printing.
• Do not remove the protective sheet applied to the bottom of the product.
  Removing it may decrease the product’s performance.
• Do not scratch or rub the body, parts, or seals with fingernails or hard objects.
  Doing so may cause damage or peeling.
• Do not use the product in a moving vehicle.
  This may result in scalds* or soiling of clothes or of the interior of the vehicle. Using the product while you are driving is very dangerous, as you may be distracted.
  * When using products that keep beverages hot.
• Do not forcibly pull on the gasket.
  The gasket cannot be removed. Damaging the gasket may result in leakage of contents.
• Do not use the product while the spout is removed.
  The beverage will spill out and cause scalds*.
  * When using products that keep beverages hot.
• Install only the parts intended for use with the product.
  If any other parts are installed, there is a risk that the contents may leak, causing scalds* or stains.
  * When using products that keep beverages hot.
• When using the product, check that there is no leakage of the beverage.
  There is a risk of the contents leaking, causing scalds* or stains. If leakage occurs, parts may not be attached correctly, the stopper part may not be attached securely, or the product may be damaged.
  * When using products that keep beverages hot.

To Page Top

Precautions when adding beverages

Caution

• Do not pour a beverage into the bottle while the stopper part is in place.
  The beverage may overflow or spill, causing scalds* or injuries to the skin. It may also cause scratching or deformation of the product.
  * When using products that keep beverages hot.
  Do not put hot beverages in the product.
  There is a risk of leakage or scalds.

• Be sure to only fill the product up to the maximum level shown in the diagram.
  If the contents exceed the specified level, they may overflow and cause scalds* or stains.
  * When using products that keep beverages hot.

  

• Be careful not to tip over the product when pouring beverages into it.
  The beverage will spill out, and there is a risk of scalds*, injuries, scratches, or deformation.
  * When using products that keep beverages hot.
• Attach the stopper part securely with the product in an upright position and check that the safety lock is engaged.
  There is a risk that the beverage may leak, causing scalds* or stains.
  * When using products that keep beverages hot.
• Never put the following things in the product.
  ●Dry ice, carbonated beverages, etc.
  The pressure inside the product may increase, causing the stopper part or lid to become stuck, the beverage to spray out, or parts to be damaged and fly off, resulting in injuries or stains.
  ●Milk, dairy products, certain fruit juices, etc.
  The contents may decay or spoil. Leaving such beverages inside the product may create gases that raise the pressure inside the product. This can cause the stopper part or lid to become stuck, the contents to spray out, or parts to be damaged and fly off, resulting in injuries or stains.
  ●Soups or beverages containing large amounts of salt.
  The contents may decay or spoil, the product may rust, or the performance of the product may decline.
  ●Tea leaves, peeled fruit, etc.
  They may cause clogging, resulting in leakage.
• Due to the structure of the product, condensation may occur if cold beverages are put in it, generating water droplets on the stopper part.

To Page Top

Precautions when carrying the product

Caution

• Do not put the product in a bottle sling, bottle boot or bag when its body is wet.
  There is a risk of rust, odors, or stains.
• Do not carry together with a PC, mobile phone, digital camera, or other electronic device.
  If the beverages leak, it could cause damage and malfunctions in electronic devices.
• Do not swing the product around by the body or stopper part.
  The product may strike other people or objects, resulting in injury or damage. If the stopper part is not properly attached or turned in the direction that loosens it or the product is subjected to strong impacts or vibration, the stopper part may come off, causing the body to fall and resulting in injury or damage.
• Do not hang the product from things by attaching it via the handle or loop attached to the lid with a metal clasp, string, or similar object.
  The body may fall, resulting in injury or damage.
• Observe the following when placing the product in automobile drink holders.
  ●Check that the product fits stably in the holder and that the holder is sufficiently strong.
  ●When using an aftermarket drink holder, use a stationary type.
  If the product falls over or tilts or the drink holder breaks or is damaged, there is a risk of scalds*, injuries, accidents, or soiling of property and the interior of the vehicle.
  * When using products that keep beverages hot.
  * The product may not fit depending on the vehicle model or type of drink holder.

To Page Top

Precautions when using the bottle boot

Caution

• Do not rub the bottle boot against anything too strongly. In addition, do not allow beverages such as coffee to remain on its surface for a long time.
  Color transfer may occur.
• Do not place on hot objects.
  There is a risk of fire, discoloration, or deformation.
• Do not hit with sharp objects.
  It may cause a hole or tear.
• Do not pull hard when removing.
  There is a risk of tears or deformation.
• Do not use paint thinner, benzine, metal scrubbing brushes, polishing powder, cleansers, or similar substances.
  They may cause tears or discoloration.
• Do not use chlorine bleach.
  This may cause tears or discoloration.
• Do not use a dishwasher or dish dryer and do not boil.
  There is a risk of discoloration or deformation.

To Page Top

Precautions when drinking

Caution

• Do not open or close the stopper part or lid if the product is tilted.
  The beverage may overflow or leak, causing stains.
• Be sure to wipe off any liquid on the spout.
  The contents may leak when the stopper part or lid is closed.
• Consume beverages as soon as possible.
  If they are left in the bottle for a long time, gases may be generated due to spoilage, raising the pressure inside the product and causing the stopper part or lid to become stuck or the beverage to spurt out. Furthermore, parts may be damaged and fly off, causing injuries and stains.

To Page Top

Precautions when cleaning

Caution

• Do not use paint thinner, benzine, metal scrubbing brushes, polishing powder, cleansers, or similar substances.
  Doing so may result in rust, scratches, or poor performance.
• Do not use chlorine bleach.
  Doing so may result in rust, paint/printing/plating peeling*, or holes.
  * For products that are painted or include printing or plating.
• Be sure to clean the product immediately after use. Even if you are out and cannot clean it fully, immediately rinse out the inside of the product with water after use.
  Failure to do so may result in mold, rust, holes, or other problems.

To Page Top