To improve the thermal retention performance, pour a small amount of hot/cold water into the main body beforehand and let it sit for 1 or 2 minutes
Discard the hot/cold water after preheating/precooling.
Pour your hot/cold beverage into the main body.
To avoid adding too much beverage, add it up to the position shown in the figure (slightly less than full).
Do not put large cubes of ice. Use small cubes or crushed ice.
Be sure to wipe off any spillage on the outside of the main body.
Putting in ice causes the pressure inside the main body to decrease, which can cause the gasket to come off when opening the inner stopper. If this occurs, reattach the gasket in its original position. (MCZ-D/F)
The color of hot tea poured into the main body may change. To avoid the risk of the inner stopper clogging when keeping tea in the product, use a teabag. (MCZ-D/F)
(G) Brim (H) Main body (N) Inner stopper B
Place the main body in an upright position and turn the stopper unit or cup unit to close it.
Check that the lid gasket and stopper gasket are attached to the stopper. (MCZ-D/E)
Check that the gaskets (S and L) are attached to inner stopper B. (MCZ-D/F)
Turn the stopper as far as it will go to securely close it. (MCZ-D/E)
Turn inner stopper A, inner stopper B, and the cup as far as they will go to securely close them. (MCZ-D/F)
Check that the stopper unit or cup unit is securely closed.
(C) Lid (E) Spout (J) Cup (K) Inner stopper A (N) Inner stopper B
To drink, hold the main body and spout, and turn the lid. (MCZ-D/E) To pour the beverage, remove the cup, press the open button, and tilt the main body. (MCZ-D/F)
Do not tilt the body immediately after pouring in a hot beverage and closing the lid. Otherwise, the contents may leak. (MCZ-D/E)
Do not shake the main body. (MCZ-D/F)
Pour the beverage slowly without tilting the main body abruptly. (MCZ-D/F)
(C) Lid (E) Spout (H) Main body (J) Cup (L) Open button (M) Close button* * The close button protrudes out laterally.
After drinking, return the product to an upright position and securely close the lid. (MCZ-D/E) After pouring, return the product to an upright position and press the close button 2 to 3 seconds later. Then attach the cup by turning it completely. (MCZ-D/F)
Turn the lid as far as it will go to securely close it. (MCZ-D/E)
Dry off any droplets remaining on the inside of the cup, and wipe well before attaching the cup. (MCZ-D/F)
(C) Lid (E) Spout (J) Cup (M) Close button
Caution
Make sure the handle on the lid does not suffer any strong impact while carrying it. The lid may open. (MCZ-D/E)
When carrying by the lid handle, use caution not to turn the product in a direction that may cause the stopper to loosen, and not to subject the product to strong vibration or impact. Make sure that the stopper does not become loose. The main body may fall off if the stopper is loosened. (MCZ-D/E)
Do not use the bottle by hanging it with any metal fittings or strings attached to the handle on the lid. Doing so may cause the main body to fall off if the stopper is loosened. (MCZ-D/E)
Do not press the close button while the main body is tilted. Otherwise, beverage may remain in the inner stopper and leak. (MCZ-D/F) (M) Close button (L) Open button
Do not keep the main body sideways. It may cause the contents to leak.
If you place the product in a bag, be sure to keep the handle on the lid away from bag contents. The lid may open. (MCZ-D/E)
When putting the product into a bag, place it standing up to prevent any possible leakage. Otherwise, the contents may leak.
